Муфты электромонтажные от производителя Fucon

Datasheet LTC1876 (Analog Devices) - 8

ПроизводительAnalog Devices
ОписаниеHigh Efficiency, 2-Phase, Dual Synchronous Step-Down Switching Controller and Step-Up Regulator
Страниц / Страница36 / 8 — TYPICAL PERFOR A CE CHARACTERISTICS. Input Source/Capacitor Instantaneous …
Формат / Размер файлаPDF / 372 Кб
Язык документаанглийский

TYPICAL PERFOR A CE CHARACTERISTICS. Input Source/Capacitor Instantaneous Current (Figure 1). Load Step (Figure 1)

TYPICAL PERFOR A CE CHARACTERISTICS Input Source/Capacitor Instantaneous Current (Figure 1) Load Step (Figure 1)

17 предложений от 12 поставщиков
DC DC Cntrlr Triple-OUT Synchronous Step Down Controller/PWM DC to DC Controller 3.5V to 36V Input 36Pin SSOP T/R
LIXINC Electronics
Весь мир
LTC1876EG#TRPBF
Linear Technology
от 329 ₽
EIS Components
Весь мир
LTC1876EG#TRPBF
Analog Devices
518 ₽
ChipWorker
Весь мир
LTC1876EG#TRPBF
Linear Technology
695 ₽
Augswan
Весь мир
LTC1876EG#TRPBF
Analog Devices
по запросу
LED-драйверы MOSO для индустриальных приложений

Модельный ряд для этого даташита

Текстовая версия документа

LTC1876
W U TYPICAL PERFOR A CE CHARACTERISTICS Input Source/Capacitor Instantaneous Current (Figure 1) Load Step (Figure 1) Load Step (Figure 1)
IIN 2A/DIV VOUT VOUT VIN 200mV/DIV 200mV/DIV 200mV/DIV VSW1 10V/DIV IOUT IOUT 2A/DIV 2A/DIV VSW2 10V/DIV 1876 G31 1876 G30 VIN = 15V 1µs/DIV V V IN = 15V IN = 15V 20µs/DIV VOUT = 5V V V OUT = 5V OUT = 5V IOUT5 = IOUT3.3 = 2A LOAD STEP = 0A TO 3A LOAD STEP = 0A TO 3A CONTINUOUS MODE Burst Mode OPERATION
Constant Frequency (Burst Burst Mode Operation (Figure 1) Inhibit) Operation (Figure 1)
VOUT VOUT 20mV/DIV 20mV/DIV IOUT IOUT 0.5A/DIV 0.5A/DIV 1876 G32 1876 G33 VIN = 15V 10µs/DIV VIN = 15V 2µs/DIV VOUT = 5V VOUT = 5V VFCB = OPEN VFCB = 5V IOUT = 20mA IOUT = 20mA
U U U PIN FUNCTIONS RUN/SS1, RUN/SS2 (Pins 1, 23):
Combination of Soft-Start,
SENSE1–, SENSE2– (Pins 3, 13):
The (–) Input to the Run Control Inputs and Short-Circuit Detection Timers. A Differential Current Comparators. capacitor to ground at each of these pins sets the ramp time
V
to full output current. Forcing either of these pins back below
OSENSE1, VOSENSE2 (Pins 4, 12):
Receives the remotely- sensed feedback voltage for each controller from an external 1V causes the IC to shut down the circuitry required for that resistive divider across the output. particular controller. Latchoff overcurrent protection is also invoked via this pin as described in the Applications Informa-
FREQSET (Pin 5):
Frequency Control Input to the Oscillator. tion section. This pin can be left open, tied to ground, tied to INTVCC or driven by an external voltage source. This pin can also be used
SENSE1+, SENSE2+ (Pins 2, 14):
The (+) Input to each with an external phase detector to build a true phase-locked Differential Current Comparator. The ITH pin voltage and loop. controlled offsets between the SENSE– and SENSE+ pins in conjunction with R
STBYMD (Pin 6):
Control pin that determines which circuitry SENSE set the current trip threshold. remains active when the controllers are shut down and/or 1876fa 8
Электронные компоненты. Скидки, кэшбэк и бесплатная доставка от ТМ Электроникс